❶ c語言編程:由鍵盤輸入一個點的坐標,判斷這個點是否在單位圓內,在的話輸出Y,否則輸出N。
應該用fabs的,abs是求整數的,fabs是求小數的,
C語言很簡單的,不需要題庫,把書上的習題和例題的代碼自己敲一遍就ok
❷ C語言關於判斷點在圓上。
float a,b;
scanf("%f,%f",&a,&b); //獲取點坐標
if(abs(a*a+b*b-1)<0.001){
printf("點在圓上");
}
else{
printf("點不在圓上");
}
❸ c語言判斷一個點在圓外還是圓內,…我用面積算得,,可是怎麼排除在圓上那個點
可以用點到圓心距離來算。
double cx,cy,r;
double x,y,d;
...
d = sqrt( (x-cx)*(x-cx) + (y-cy)*(y-cy));
if (d > r){ 內
} else if (d < r){ 外
} else {
圓周上
}
排除內,外。
因浮點數比較,難用 等於 判斷,一般用 fabs(差)< eps; eps = 1e-10
❹ 任意輸入點的坐標,判斷該點是否在圓環內(x2+y2>=1 x2+y2<=4 )的c語言程序怎麼寫急!!
#include "stdio.h"
int main()
{
double x,y;
printf("請輸入點坐標:");
scanf("%lf,%lf",&x,&y);
if(x*x+y*y>=1 && x*x+y*y<=4)
printf("該點在圓環(x^2+y^2>=1 x^2+y^w<=4)內! ");
else
printf("該點不在圓環內! ");
}
注意輸入坐標時,中間用逗號隔開
❺ 一道c語言編程題目 請編寫一個程序實現:判斷平面上的某個點是否在某個圓的內部。要求如下: 1)定
#include<stdio.h>
typedef struct PP
{double x,y;}POINT;
typedef struct CC
{POINT O;
double r;}CIRCLE;
int incircle(POINT p,CIRCLE c1)
{return ((p.x-c1.O.x)*(p.x-c1.O.x)+(p.y-c1.O.y)*(p.y-c1.O.y)<=c1.r*c1.r);}
int main()
{POINT p1,p2;
CIRCLE C;
p1.x=1.0;
p1.y=1.0;
p2.x=-1.0;
p2.y=2.0;
C.O.x=0;
C.O.y=0;
C.r=2.0;
printf("%d ",incircle(p1,C));
printf("%d ",incircle(p2,C));
return 0;
}
❻ 求一點是否在圓內的c語言程序
#include <stdio.h>
int main()
{
float o[]={0,0}; //圓心的位置
float r,d; //半徑r,點A到圓心的距離d
float A[1]; //點A的位置
printf("假設圓心位置為(0,0),請輸入圓的半徑r:\n");
scanf("%f",&r);
printf("圓的半徑r=%.2f\n",r);
printf("請輸入點A的橫坐標:\n");
scanf("%f",&A[0]);
printf("請輸入點A的縱坐標:\n");
scanf("%f",&A[1]);
d=A[0]*A[0]+A[1]*A[1];
r=r*r;
if (r>d)
{
printf("點A在圓內。\n");
}
else if (r<d)
{
printf("點A在圓外。\n");
}
else
printf("點A在圓上。\n");
return 0;
}